|
1 rIN I
<br /> r; a � ° r �.'€ e r r ' I NNI NN
<br /> n c 43
<br /> x
<br /> .. It,
<br /> NZIa
<br /> r., . - =.c
<br /> .. -+' ( a z,a r.,4 ,aa '.. . , ,+ ` . wu+ 3 + . , , t .. 'a., ' z a ;ti.: ,�"n,. €..
<br /> atY. - . '•: -n ,t��� ,c; � -s L
<br /> : h't' t "�" % a-r�., ``. 'rrrr ,1 ,. 'd ,,i , r,;' `x`°^"3-s ` 3x�a?? ,..'. k ;v k�,
<br /> ,' acs. ` t N , NIN .AN
<br /> IN IN
<br /> SUPERPAVE PG ASPHALT BINDER
<br /> Specification
<br /> Test and Method Conditions Minimum/Maximum
<br /> Value
<br /> Original Binder
<br /> Superpave PG Asphalt
<br /> Binder Grade Report
<br /> Qualified Products List
<br /> IN Number Report
<br /> Polymer Modifier Type (PG 76 -22 Only) Report
<br /> Solubility, AASHTO T 44 in Trichloroethylene Minimum 99 . 0 %
<br /> Flash Point, AASHTO T 48 COC Minimum 450°F IN
<br /> Rotational Viscosity, 275 °F Maximum 3 Pa- s
<br /> AASHTO T 316
<br /> Absolute Viscosity, 140°F Max . 2400 P (PG 64 -22)
<br /> AASHTO T 202 Max . 3600 P (PG 67 - 22 ) IN
<br /> IN
<br /> Dynamic Shear Rheometer G /sin S, Test Temperature @
<br /> 10 rad/sec , ° C Minimum 1 . 00 kPa IN
<br /> AASHTO T 315 phase Angle , b , (PG 76 -22 Only) Maximum 75 degrees
<br /> IN Rolling Thin Film Oven Test Residue (AASHTO T 240)
<br /> Rolling Thin Film Oven , IN I
<br /> AASHTO T 240 Mass Loss % Maximum 0 . 50
<br /> Dynamic Shear Rheometer, G /sin 6 , Test Temperature @
<br /> AASHTO T 315 10 rad/sec, ° C Minimum 2 . 20 kPa IN I
<br /> Pressure Aging Vessel Residue (AASHTO R 28 ) at 100°C
<br /> Dynamic Shear Rheometer, G sin S , Maximum 5000 kPa
<br /> AASHTO T 315 10 rad/sec . 25 ° C
<br /> S ( Stiffness) , @
<br /> Creep Stiffness , 60 sec . @ - 12 ° C Maximum 300 Mpa
<br /> AASHTO T 313 M-value , @
<br /> 60 sec . @ - 12 ° C Minimum 0 . 300
<br /> IN
<br /> IN IN
<br /> 9164 .3 . 5 Notification and Evaluation : In the event that a Specification
<br /> Compliance test is outside specification requirements or a Quality Control test is outside limits
<br /> established by the supplier as part of his Quality Control Program shipments of that product to
<br /> Department projects will cease immediately and the Contractor and the State Materials Office
<br /> will be notified and the product retested for Specification Compliance (resampling as
<br /> appropriate) . Where the retest for Specification Compliance meets all requirements , shipments of
<br /> that product may resume . Where off. specification material has been shipped and the retest
<br /> confirms the original test, the Contractor and State Materials Office will be informed of the steps
<br /> taken to achieve specification compliance on the product shipped .
<br /> Where off- specification materials has been shipped, further shipment of
<br /> that product to Department projects shall remain suspended until the cause of the problem is
<br /> evaluated and corrected by the supplier to the satisfaction of the State Materials Engineer.
<br /> - 208 -
<br /> FPID ( S ) : 423186 - 1 - 58 - 01
<br /> i as �, "`m a t " t g i �` r v s.
<br /> „ � x � .;. . .,_ xm- � , . �. e. : 2 � ,hi X .` Z, ,.. .k.` ,. . . , � �, w.. . n .. , � ,,. ,. � .,
<br />. . 11 � . s .,.,
<br />
|