Laserfiche WebLink
en <br /> ZI nn <br /> ell ell <br /> Y <br /> >. , t s.. 'a n �" 'firt4° '< 114 1 <br /> '�"a ^tis . Inell <br /> Parameters Limits <br /> Pour Point t least 20 ° lower than the safe heating temperature as stated by the <br /> manufacturer . <br /> Cone-Penetration , Non- <br /> immersed at 77 °F , 150 g, 5 s Less than or equal to 90 mm <br /> low at 40 °F , 5 hLess than or equal to 3 . 0 mm <br /> No cracking, separation , or opening that at any point is over <br /> ond, Non-immersed, -20 °F <br /> or 3 cycles , 50 % extension * 1 /4 inch deep, in the sealant or between the sealant and the <br /> substrate , <br /> Resilience at 77 ° F Recovery greater than orequal to 60 % <br /> o failure in adhesion, formation of an oily exudates at the <br /> Asphaltic Concrete interface between the sealant and the asphaltic concrete, or <br /> Compatibility at 140 °F softening or other deleterious effects on the asphaltic concrete or <br /> sealant. <br /> *The depth of a crack, separation opening shall be measured perpendicular to the side of the sealant showing the defect. At <br /> east two test samples in a group of three representing a given sample of sealant shall meet this requirement. <br /> SUBARTICLE 9324 . 2 . 4 (Page 879) is deleted and the following substituted : <br /> 9324 . 2 .4 Qualified Products List : The joint sealant materials used shall be one <br /> of the products listed on the Department ' s Qualified Products List (QPL) . Manufacturers seeking <br /> evaluation of their products shall submit product datasheets , performance test reports from an <br /> independent laboratory showing the product meets the requirements of this section , and a QPL <br /> application in accordance with Section 6 . Information on the QPL application must identify the <br /> sealant type . <br /> SUBARTICLE 9324 . 3 . 2 (Pages 880 - 882 ) is deleted and the following substituted : <br /> 9324 .3 .2 Physical Requirements : <br /> SILICONE Test Method Type A <br /> SEALANT TYPE Yh Type B Type C Type D <br /> Flow (maximum) MIL S 8802 0 . 3 inches <br /> Extrusion rate MIL S 8802 1 . 254 . 2 g/s 1 . 7 - 11 . 0 g/s 4 . 58 - 9 . 2 g/s 3 . 3 — 9 . 2 g/s <br /> ack- free time at 77 MIL S 8802 <br /> 3 °F and 45 to 20 - 75 120 minutes , 60 minutes , 30 - 60 <br /> 55 % Relative minutes maximum maximum minutes <br /> Humidity <br /> Specific gravity ASTM D 792 , 1 . 1 to 1 . 515 1 . 10 to 1 . 40 1 . 26 to 1 . 34 1 . 26 <br /> to 1 . 34 <br /> Method A <br /> Durometer <br /> hardness , Shore A ASTM D 2240 10 -25 <br /> (Cured seven days <br /> -214 - <br /> FPID (S ) : 423186 - 1 - 58 - 01 <br /> ell en- <br /> le <br /> ell nee ney nn I, e In <br /> vX <br /> 1-11177 n� In <br /> LL In <br /> In In <br /> ne- <br /> z . . ' nee <br /> ,. os .. . , ._ � . ,. . , , .. . . . . . ,. ,, . . ell ll . . <br /> ,.w ,. . ., . , . . In <br />