12/1/1997 - Laserfiche WebLink

Home Browse Search

(i) In cases where the abutting useldistrict is separated from the project site by a local road. the buffer We shall be reduced one catego1y We (e.g. from Type "A" or Lme "B"). but the height of the opaque feature shall remain the same In uses where the abutting use/district is separated from the project site by a Thoroughfare Plan road, the buffer type shall be reduced two category types (e.g. "A" to "C") but in all cases shall require at least a Type "D" buffer. Reference section 915.16(3). 01 Required 3' and 6' opaque features shall be measured from the finished floor elevation of the proposed structure(s). This requirement can be modified by the Planningand Zoning Commission based upon gElde differences and the relationship between the height and mass of the proposed building and its setback from the property line. The maximum required hekht of an onaaue feature shall be 8' above the site grade where the feature is located u Hedge or shrub material within buffers may be reduced by 50'/o when a 6' wall or fence is provided within the buffer if the remaining amount of requirrd shrub material and at least 50% of required understoly tree material are lanted between the project site perimeter and the wall or fence Alternative planting locations may be approved by the Planning and Zoning Commission The standards for the buffer categories are set forth in the illustrations herein that specify the number of plants required per one hundred (100) lineal feet. To determine the total number of plants required, the linear footage of each side of the property requiring a buffer shall be divided by one hundred (100) and multiplied by the number of plants shown in the illustration. The plants shall be spread in a reasonably even manner along the length of the buffer. Buffer opaque feature options are also illustrated herein and are further defined in Chapter 901, Definitions, of the County Land Development Code. 5. BUFFERS BETWEEN COMMERCIAL & RESIDENTIAL Amend zoning chapter section 911.10(8), as follows (8) Required buffer yards: Notes: Buffer yards are required along rear/side property lines and measured at right angles to lot lines. All screening and buffering requirements shall meet the standards established in section 926, Landscaping and Buffering. No parking or loading shall be permitted within buffer yards. Note- When a lnari;^p pock is ptoposed to serve a use that normallLregutres fent dock use/e g_Mcery st_ ori d Parrment store. bip box retain. and :s to be located adiacent to a residentially designated site and will not be screened one view from an adiacent residential site by an interpeninr buiIdMne or s_tractare. m 8' high wall shall be required between the loading dock and the restderrttal site Wall height shall be measured from the grade elevation of the parldna are s adiacent to the loading dock Plantings along the wall are renuired in a rdance with the standards of landscape section 926.08. 6. BUFFERS BETWEEN INDUSTRIAL & RESIDENTIAL Amend zoning chapter section 911.11(7), as follows: (7) Buffer yard requirements. Where a nonresidential use within an industrial district directly abuts a single family or multi -family residential zoning district or use, a landscaped buffer yard meeting the following specifications shall be required along the side and/or rear property lines. District Single Family Zoning Multi -Family Zoning IL Type A 6 R Opaque Feature IGType A 6 & Opaque Feature Type A 61 Opaque Feature Type A 6 R Opaque Feature DECEMBER 1, 1997 -17- BOOK Abutting Use/District Single Family Multi -Family District Buffer Type Buffer Type PRO C - 6 ft. Opaque D - 3 ft. Opaque OCR C - 6 ft. Opaque D - 3 ft. Opaque MED C - 6 ft. Opaque D - 3 ft. Opaque CN B - 6 ft. Opaque C - 6 ft. Opaque CL B - 6 ft. Opaque C - 6 ft. Opaque CG 8 - 6 ft. Opaque C - 6 ft. Opaque CH B - 6 ft. Opaque B - 6 ft. Opaque Notes: Buffer yards are required along rear/side property lines and measured at right angles to lot lines. All screening and buffering requirements shall meet the standards established in section 926, Landscaping and Buffering. No parking or loading shall be permitted within buffer yards. Note- When a lnari;^p pock is ptoposed to serve a use that normallLregutres fent dock use/e g_Mcery st_ ori d Parrment store. bip box retain. and :s to be located adiacent to a residentially designated site and will not be screened one view from an adiacent residential site by an interpeninr buiIdMne or s_tractare. m 8' high wall shall be required between the loading dock and the restderrttal site Wall height shall be measured from the grade elevation of the parldna are s adiacent to the loading dock Plantings along the wall are renuired in a rdance with the standards of landscape section 926.08. 6. BUFFERS BETWEEN INDUSTRIAL & RESIDENTIAL Amend zoning chapter section 911.11(7), as follows: (7) Buffer yard requirements. Where a nonresidential use within an industrial district directly abuts a single family or multi -family residential zoning district or use, a landscaped buffer yard meeting the following specifications shall be required along the side and/or rear property lines. District Single Family Zoning Multi -Family Zoning IL Type A 6 R Opaque Feature IGType A 6 & Opaque Feature Type A 61 Opaque Feature Type A 6 R Opaque Feature DECEMBER 1, 1997 -17- BOOK