Laserfiche WebLink
In In I <br /> performance . Warm mix technologies (additives , foaming techniques , etc . ) listed on the <br /> Department ' s website may be used in the production of the mix . The URL for obtaining this <br /> information, if available , is : <br /> www. dot. state . fl . us/Specificationsoffice/implemented/URLinSpecs/files/WarmMixAsphalt . pdf . <br /> 337-2 .2 Asphalt Binder : Meet the requirements of Section 336 , and any additional <br /> requirements or modifications specified herein for the various mixtures . When called for in the <br /> Contract Documents , use a PG 76 -22 asphalt binder meeting the requirements of 916 - 1 . For <br /> projects with a total quantity of FC-5 , FC -9 . 5 , or FC42 . 5 less than 500 tons , the Contractor may <br /> elect to substitute a PG 76 -22 for the ARB - 12 or ARB - 5 , meeting the requirements of 9164 . <br /> 337-2 .3 Coarse Aggregate : Meet the requirements of Section 901 , and any additional <br /> requirements or modifications specified herein for the various mixtures . <br /> 3371m2 .4 Fine Aggregate : Meet the requirements of Section 902 , and any additional <br /> requirements or modifications specified herein for the various mixtures . <br /> 337-2 . 5 Hydrated Lime : Meet the requirements of AASHTO M 303 , Type 1 . <br /> Provide certified test results for each shipment of hydrated lime indicating <br /> compliance with the specifications . <br /> 337-2 . 6 Liquid Anti-strip Additive : Meet the requirements of 916 - 5 and be listed on the <br /> Department ' s Qualified Products List (QPL) . <br /> 337-2 . 7 Fiber Stabilizing Additive (Required for FC-5 only) : Use either a mineral or <br /> cellulose fiber stabilizing additive . Meet the following requirements . <br /> 337-2 . 7. 1 Mineral Fibers : Use mineral fibers (made from virgin basalt, diabase , <br /> or slag) treated with a cationic sizing agent to enhance the disbursement of the fiber, as well as to <br /> increase adhesion of the fiber surface to the bitumen . Meet the following requirements for <br /> physical properties : <br /> 1 . Size Analysis <br /> Average fiber length : 0 . 25 inch (maximum) <br /> Average fiber thickness : 0 . 0002 inch (maximum) <br /> 2 . Shot Content (ASTM C612) <br /> Percent passing No . 60 Sieve : 90 - 100 <br /> Percent passing No . 230 Sieve : 65 - 100 <br /> Provide certified test results for each batch of fiber material indicating <br /> compliance with the above tests . <br /> 337-2 . 7.2 Cellulose Fibers : Use cellulose fibers meeting the following <br /> requirements : <br /> 1 . Fiber length : 0 . 25 inch (maximum) <br /> 2 . Sieve Analysis <br /> a. Alpine Sieve Method <br /> Percent passing No . 100 sieve : 60 - 80 <br /> b . Ro-Tap Sieve Method <br /> Percent passing No . 20 sieve : 80 - 95 <br /> Percent passing No . 40 sieve : 4545 <br /> Percent passing No . 100 sieve : 5 -40 <br /> 3 . Ash Content : 18 % non-volatiles (plus or minus±5 %) <br /> 4 . pH : 7 . 5 (plus or minus± 1 . 0) <br /> 5 . Oil Absorption : 5 . 0 % (plus or minus± l . 0) (times fiber weight) <br /> 6 . Moisture Content : 5 . 0 % by weight (maximum) <br /> - 102 - <br /> FPID ( S ) : 423186 - 1 - 58 - 01 <br />