Laserfiche WebLink
Specifications: SlideDriver 50VF2/3 (222 X3 ST) <br />6. Gate edge and transmitter radio reversing device. <br />7. HY-5A plug in type vehicle detectors. <br />8. Hy8RelayTM provides eight additional programmable user relay outputs. <br />9. Communications package delivering Internet Protocol (RJ -45 copper or SFP fiber), managed <br />switch and web based interface to operator via HyNetTM Gateway. <br />10. Key operated cable manual release (secure side of gate). <br />11. Pneumatic remote gate release devices. Places operator in "manual mode" from remote location <br />(lockable box on public side of gate). <br />12. 208/230 VAC single phase and 208/230/460 VAC three phase available. 115 VAC single phase is <br />not available. (50 Hz is available, specify voltage) <br />13. Other models available for gate speeds from 1 to 3 ft/s (304 mm/s - 914 mm/s). <br />14. Stainless steel chassis and cover, painted, for marine, caustic, or other extreme environments. <br />15. Stainless steel chassis 2B finish and cover brushed finish, for marine, caustic, or other extreme <br />environments. <br />16. Hot dip galvanized chassis and cover, unpainted, for marine, caustic, and other extreme <br />environments. <br />17. Hot dip galvanized chassis and stainless steel cover, unpainted, for marine, caustic, or other <br />extreme environments. <br />18. Available Modular configuration which includes separate metal enclosure to house electrical <br />control box, pump, and electric motor assembly. <br />19. HySecurity factory drive rail. <br />20. XtremeDriveTM System: a rack and pinion -like design, increases traction for heavy gates or for <br />sites located in harsh environments. <br />21. Lock for operator cover. <br />22. Electric Solenoid gate panel deadbolt lock. <br />23. Special Correctional Facilities models with heavy, 10 Ga. (3 mm) locking cover to withstand <br />physical attack. <br />24. UPS AC battery backup for systems up to 1 hp or VFD equipped. 208/230 VAC single phase <br />only. 115 VAC single phase not available. <br />2.3. FACTORY TESTING <br />A. Fully assemble and test, at the factory, each gate operator to assure smooth operation, sequencing <br />and electrical connection integrity. <br />B. Proof test with simulated physical and electrical loads to exceed the fully rated capacity of the operator <br />components. <br />C. Inspect and test all hydraulics are leak free. <br />D. All testing data shall be individually logged and recorded by serial number. <br />E. Check all mechanical connections for tightness and alignment. Check all welds for completeness and <br />continuity. <br />F. Inspect finishes for completeness. Touch up imperfections prior to shipment. <br />G. Check all hydraulic hoses and electrical wires to assure that chafing cannot occur during shipping or <br />operation. <br />PART 3 — EXECUTION <br />3.1. SITE EXAMINATION <br />A. Locate concrete mounting pad in accordance with approved shop drawings and in compliance with <br />local building codes. <br />B. Make sure that gate is operating smoothly under manual conditions before installation of gate <br />operators. Do not proceed until gate panel is aligned and operates without binding. <br />3.2. INSTALLATION <br />A. Install gate operator in accordance with the safety regulations and the manufacturer's product <br />literature and installation instructions, current at the time of installation. Coordinate locations of <br />operators with contract drawings; other trades and shop drawings. <br />B. Installer shall ensure that the electrical service to the operator is at least 20A. Electrical wiring to <br />conform to NEC and manufacturer's installation instructions. SlideDriver 50VF2/3 is 2400W. <br />www.hysecurity.com <br />Specification D0677 <br />